Mobile Photo Documentation App
Capture images on-site with the mobile app and sync them directly to your blasting inspection report for a complete visual record.
Mobile AppReport
Blasting Inspection Report
Verify compliance with blasting safety regulations using this comprehensive inspection report template. Document pre-blast checks (design approval, charge placement, stemming, safety zone, warning signals), blast monitoring (vibration, air overpressure, fly rock), and post-blast inspection (muck pile, fumes, ground condition, misfires). Open the template in our online editor to begin.
Open the template and create your inspection report
The full inspection cycle — in one service
Take photos of the object in the mobile app, complete the inspection report from the template, and download the finished photo report as Word or PDF.
Inspection report
Complete the document from this template: sections, fields, photo documentation, and signatures.
Photo Report Generator
Attach photos of the blast site, charge placement, muck pile, and any fly rock zones to your inspection report using the photo report generator.
Create Photo ReportReport
Document Preview
Review the structure, sections, and fields before proceeding to fill out the document.
Blasting Inspection Report
No.BL-2026-042
1. General Information
The general information about the inspection, including the date, location, and purpose, is provided below.
| Inspection date | 7/14/2026 | Time | 7:00 AM — 8:30 AM |
| Address | Bench 5, East Pit, Pine Creek Mine | Basis for inspection | MSHA Part 56 and company blasting plan |
Expert Michael Evans , Blasting Inspector
The inspection was conducted in accordance with the approved schedule and applicable regulations.
2. Object of Inspection
The object of inspection is the mine workings, including all accessible underground openings, drifts, and shafts.
| Object name | East Pit Bench 5 |
The mine workings were identified and their boundaries were confirmed as per the mine plan.
3. Pre-Blast Checks
The main parameters of the mine workings, such as dimensions, support type, and ventilation, were measured and compared with design values.
| Blast Design Approved | No | Charge Placement Verified | No |
| Stemming Adequate | No | Safety Zone Established | No |
| Warning Signals Checked | No |
The measured parameters are within acceptable tolerances, with minor deviations noted in the relevant sections.
4. Blast Monitoring
Additional parameters including geological conditions, water inflow, and gas concentrations were assessed during the inspection.
| Vibration Level: 12.5 | Air Overpressure: 115 |
| ☐ Fly Rock Observed |
No significant anomalies were detected in the additional parameters.
5. Inspection Conditions
The overall condition of the mine workings was evaluated, including the state of supports, walls, and floors.
Inspection conditions are not selected.
The mine workings are generally in a safe and serviceable condition, with some areas requiring maintenance.
6. Defects and Observations
List post-blast defects and observations such as ground instability or cracks.
| No. | Damage description | Photos |
|---|---|---|
| 1 | - | not filled in |
7. Additional Information
Provide overall assessment of blast success and recommendations.
| Identification was carried out | Blast #B-042, Location: East Pit Bench 5 |
| There are remarks | Blast successful. No misfires. Vibration within limits. |
8. Inspection Participants
List the inspector and blasting supervisor involved.
| No. | Full name | Position / status | Comment |
|---|---|---|---|
| 1 | Michael Evans | Blasting Inspector | Lead inspector |
| 2 | John Miller | Blasting Supervisor | Supervised blast |
Signatures
Capture signatures of the inspector and blasting supervisor.
______________________________
Michael Evans, Blasting Inspector
______________________________
Michael Evans
______________________________
John Miller
Report
Purpose and Procedure for Drafting the Document
What Is a Blasting Inspection Report?
A blasting inspection report is a document used to verify compliance with blasting safety regulations. It includes pre-blast checks, blast monitoring data, and post-blast inspection results. The template covers design approval, charge placement, stemming, safety zone, warning signals, vibration levels, air overpressure, fly rock, muck pile condition, fumes, ground condition, and misfires. This structured format ensures all critical aspects are documented.
Key Sections of the Template
The template includes sections for report metadata, pre-blast check, blast monitoring, post-blast inspection, defects and observations, conclusions, and signatures. Each section contains fields for specific checks and measurements.
Who Uses This Document?
Blasting inspectors, safety officers, and blasting supervisors use this report to document blasting operations. It supports compliance with safety regulations and provides a record for each blast.
Before and After Each Blast
This report is completed for every blast to ensure all safety checks are performed and documented. It provides a complete record of the blasting event.
Regulatory Compliance
Mining regulations often require blasting inspection reports. This template helps meet those requirements by providing a standardized format.
Incident Investigation
If an incident occurs during blasting, the inspection report provides critical data for investigation, including pre-blast conditions and monitoring results.
Performance Analysis
Engineers use the data from multiple reports to analyze blasting performance, optimize blast designs, and improve safety.
Training and Audits
The reports serve as training material for new blasting personnel and as evidence during safety audits.
- 1
Open the Template
Open the blasting inspection report template in the online editor. The template is pre-configured with all necessary sections and fields.
- 2
Complete Pre-Blast Checks
Enter the inspection date, blast location, and blast number. Verify and document each pre-blast check item.
- 3
Monitor and Record Blast Data
During the blast, record vibration levels, air overpressure, and whether fly rock was observed. After the blast, inspect the muck pile, fumes, ground condition, and check for misfires.
- 4
Finalize and Sign
Provide an overall assessment of blast success and any recommendations. Add signatures of the inspector and blasting supervisor, then export the report.
Photo Report Generator
Attach photos of the blast site, charge placement, muck pile, and any fly rock zones to your inspection report using the photo report generator.
Create Photo ReportMobile Photo Documentation App
Capture images on-site with the mobile app and sync them directly to your blasting inspection report for a complete visual record.
Mobile AppDocument Sections
Click a section to jump to it in the sample document.
General Information
The general information about the inspection, including the date, location, and purpose, is provided below.
Object of Inspection
The object of inspection is the mine workings, including all accessible underground openings, drifts, and shafts.
Pre-Blast Checks
The main parameters of the mine workings, such as dimensions, support type, and ventilation, were measured and compared with design values.
Blast Monitoring
Additional parameters including geological conditions, water inflow, and gas concentrations were assessed during the inspection.
Inspection Conditions
The overall condition of the mine workings was evaluated, including the state of supports, walls, and floors.
Defects and Observations
List post-blast defects and observations such as ground instability or cracks.
Additional Information
Provide overall assessment of blast success and recommendations.
Inspection Participants
List the inspector and blasting supervisor involved.
Signatures
Capture signatures of the inspector and blasting supervisor.
Document Fields and Columns
General Information
- Inspection date
- Date of the inspection.
- Time
- Time of the inspection.
- Address
- Location of the blast site.
- Basis for inspection
- Regulatory basis for the inspection.
- Expert
- Name of the inspector.
Object of Inspection
- Object name
- Blast location and blast number.
Defects and Observations
- No.
- Sequential number of the finding.
- Element
- Component or area affected.
- Defect
- Type of defect or observation.
- Localization
- Exact location of the finding.
- Photos
- Photographic evidence.
- Damage description
- Detailed description of the finding.
Inspection Participants
- No.
- Sequential number of the participant.
- Full name
- Full name of the participant.
- Position / status
- Role or job title.
- Comment
- Additional remarks.
Frequently Asked Questions about Photo Reports and Photo Tables
What is a blasting inspection report?
A blasting inspection report is a document used to verify compliance with blasting safety regulations. It includes pre-blast checks, blast monitoring data (vibration, air overpressure, fly rock), and post-blast inspection results. The template helps ensure all safety aspects are documented for each blast.
Who signs the blasting inspection report?
The inspector who conducts the inspection and the blasting supervisor who oversees the blast typically sign the report. Their signatures confirm that all checks were performed and the blast was conducted safely.
Can I include photos in the report?
Yes, the template supports attaching photos of the blast site overview, charge placement, post-blast muck pile, fly rock zone, and safety signage. Using the photo report generator or mobile app, you can easily add visual evidence.
How often is a blasting inspection report required?
A blasting inspection report is required for every blast, with pre-blast and post-blast inspections. The exact frequency depends on the blasting schedule and regulatory requirements.
How do I start using this template?
Click the 'Use this template' button to open it in our online editor. You can then fill in the fields, add photos, and export the completed report. No download is required.
Create Your Document Online
Enter inspection details and generate a ready-to-download document.